Claude
ff0711b927
- scripts/build-bay-map.sh: maps physical drive bays to /dev/disk/by-id paths - scripts/gpu-passthrough-setup.sh: configures IOMMU + vfio-pci for two Quadro P2200s - scripts/fan-control.sh: ipmitool daemon to prevent iDRAC from running fans at 100% due to non-Dell PCIe cards; adjusts speed by inlet temperature - scripts/fan-control.service: systemd unit for fan-control.sh https://claude.ai/code/session_01TxTSnxDjgEVuNztdsWQjMD
124 lines
3.3 KiB
Bash
Executable File
124 lines
3.3 KiB
Bash
Executable File
#!/usr/bin/env bash
|
||
# Dell R730xd fan speed control for third-party PCIe cards (Quadro P2200, etc.)
|
||
#
|
||
# iDRAC detects non-Dell GPUs and slams fans to 100% indefinitely.
|
||
# This script disables iDRAC automatic fan control and manages speed based
|
||
# on inlet temperature, keeping the server quiet under normal load.
|
||
#
|
||
# Install:
|
||
# apt install ipmitool
|
||
# cp fan-control.sh /usr/local/sbin/fan-control.sh
|
||
# chmod +x /usr/local/sbin/fan-control.sh
|
||
# cp fan-control.service /etc/systemd/system/
|
||
# systemctl daemon-reload && systemctl enable --now fan-control.service
|
||
#
|
||
# Manual speed test (without running as daemon):
|
||
# fan-control.sh --set 25 # set fans to 25% and exit
|
||
# fan-control.sh --auto # restore iDRAC automatic control and exit
|
||
|
||
set -euo pipefail
|
||
|
||
IPMI="ipmitool raw 0x30 0x30"
|
||
|
||
# Fan speed thresholds by inlet temperature (°C → % speed)
|
||
# Tune these for your environment. Inlet temp sensor reads ambient air entering front.
|
||
declare -A SPEED_MAP=(
|
||
[0]=15 # < 30°C → 15% (near-silent)
|
||
[30]=20 # 30–39°C → 20%
|
||
[40]=30 # 40–44°C → 30%
|
||
[45]=40 # 45–49°C → 40%
|
||
[50]=55 # 50–54°C → 55%
|
||
[55]=75 # 55–59°C → 75%
|
||
[60]=100 # ≥ 60°C → 100% (safety)
|
||
)
|
||
|
||
# Minimum speed floor — never go below this (protects drives and CPUs)
|
||
MIN_SPEED=15
|
||
|
||
get_inlet_temp() {
|
||
ipmitool sdr type Temperature 2>/dev/null \
|
||
| grep -i "Inlet Temp\|Ambient\|Inlet" \
|
||
| grep -oP '\d+(?= degrees)' \
|
||
| head -1 || echo "35" # safe default if sensor read fails
|
||
}
|
||
|
||
pct_to_hex() {
|
||
printf '0x%02x' "$(( $1 < 100 ? $1 : 100 ))"
|
||
}
|
||
|
||
set_fan_speed() {
|
||
local pct=$1
|
||
[[ $pct -lt $MIN_SPEED ]] && pct=$MIN_SPEED
|
||
local hex
|
||
hex=$(pct_to_hex "$pct")
|
||
$IPMI 0x02 0xff "$hex"
|
||
}
|
||
|
||
disable_auto_fan() {
|
||
$IPMI 0x01 0x00
|
||
echo "$(date): iDRAC automatic fan control DISABLED"
|
||
}
|
||
|
||
enable_auto_fan() {
|
||
$IPMI 0x01 0x01
|
||
echo "$(date): iDRAC automatic fan control RE-ENABLED"
|
||
}
|
||
|
||
speed_for_temp() {
|
||
local temp=$1
|
||
local speed=$MIN_SPEED
|
||
for threshold in $(echo "${!SPEED_MAP[@]}" | tr ' ' '\n' | sort -n); do
|
||
[[ $temp -ge $threshold ]] && speed=${SPEED_MAP[$threshold]}
|
||
done
|
||
echo "$speed"
|
||
}
|
||
|
||
# ── Argument handling ─────────────────────────────────────────────────────────
|
||
|
||
case "${1:-}" in
|
||
--auto)
|
||
enable_auto_fan
|
||
exit 0
|
||
;;
|
||
--set)
|
||
pct="${2:?Usage: fan-control.sh --set <0-100>}"
|
||
disable_auto_fan
|
||
set_fan_speed "$pct"
|
||
echo "$(date): Fans set to ${pct}%"
|
||
exit 0
|
||
;;
|
||
--temp)
|
||
echo "Inlet temp: $(get_inlet_temp)°C"
|
||
exit 0
|
||
;;
|
||
"")
|
||
# Daemon mode — fall through to loop
|
||
;;
|
||
*)
|
||
echo "Usage: $0 [--auto | --set <pct> | --temp]"
|
||
exit 1
|
||
;;
|
||
esac
|
||
|
||
# ── Daemon loop ───────────────────────────────────────────────────────────────
|
||
|
||
trap 'enable_auto_fan; exit 0' SIGTERM SIGINT
|
||
|
||
echo "$(date): Fan control daemon starting"
|
||
disable_auto_fan
|
||
|
||
last_speed=-1
|
||
|
||
while true; do
|
||
temp=$(get_inlet_temp)
|
||
target=$(speed_for_temp "$temp")
|
||
|
||
if [[ $target -ne $last_speed ]]; then
|
||
set_fan_speed "$target"
|
||
echo "$(date): Inlet ${temp}°C → fans ${target}%"
|
||
last_speed=$target
|
||
fi
|
||
|
||
sleep 30
|
||
done
|